The support and help which includes the. You are welcome to share Birch integration expertise in the. Driver CD with Manual: initial: BT-482 series: Driver. CD-108e The Powerful. As a CCD Scanner expertise, Birch introduces the new CD-108e. No Operation Manual is needed for setting. Consult Birch Technology Inc.' S CD-108e brochure on DirectIndustry. Birch CD-108E Pdf User Manuals. View online or download Birch CD-108E Manual.

• Table of Contents Introduction..3 Installation.. 4 Pin Assignments.. 5 Method of Programming..7 Interface selection..10 Reading Mode..11 RS –232 Communication Parameters.12 Keyboard Wedge Parameters..14 Output Characters Parameters.16 Wand Emulation..17 OCIA Mode Parameters..18 Bar Code Type Selection..21 UPC/EAN/JAN.. • Table of Contents Reading Level.. 53 Accuracy..53 Sensitivity of Continuous Reading Mode. 53 Buzzer Beep Tone..54 PnP/Notebooks..54 Reverse Output Characters..

54 Setup Deletion.. 55 Setup Insertion.. 59 Appendix A..63 Appendix B..64 Appendix C..68. • Introduction Thank you for selecting Birch barcode input product, CD- 108E CCD barcode reader. The reader is equipped with up to date optical technology.

It auto-discriminates nearly twenty different kinds of barcode symbologies. Birch also provides other barcode related products to meet your application. • Installation Installing the Keyboard Wedge Reader To install a keyboard wedge reader, follow the steps below: 1. Turn off the power of the PC or Terminal. Unplug keyboard from the PC or Terminal.

Make sure you have the Y Cable with appropriate connector type for your PC or Terminal. • Pin Assignments 1. Keyboard Output DIN 5 MALE DIN 5 FEMALE Pin No.

Function Pin No. Install After Dark Windows 7. Function HOST CLK KB CLK HOST DATA KB DATA Vcc(+5V) Vcc(+5V) DIN 5 Male DIN 5 Female Pin Assignment Pin Assignment MiniDIN 6 MALE MiniDIN 6 FEMALE Pin No.

• Pin Assignments RS-232 Output DB 9 Female Pin No. Function Power Lead Vcc +5V DB 9 Female Pin Assignment Male DC Jack WAND Emulation Output DB 9 Female Pin No. Function DATA Vcc (+5V) DB 9 Female Pin Assignment. • Method of Programming Setup Flow Chart Start Recall Set All Configuration Parameters Defaults Interface Selection Input Port Selection Communication Parameters Bar Codes Parameters MSR Parameters Misc. Parameters etc. Abort Configuration Configuration Save Parameters Loop of Programming The philosophy of programming parameters has been shown on the flow chart. • Method of Programming Factory Default Settings The factory default settings are shown with and bold in the following sections.

You can make your own settings by following the procedures in this manual. If you want to save the settings permanently, you should scan the label of 'Save Parameters'. • Setup Commands Save Parameters Save the parameter settings%$ + / 0 permanently. R.s.agarwal Reasoning Book Pdf here.

Recall Stored Parameters%$ + / 1 Replace the current parameters by which you had saved last time. Set All Defaults Set all the parameters to the factory default settings.%$ + / 2 Start Configuration%$ + / 3. • Interface Start Configuration Interface Selection%0 0 U0 RS232 Mode%0 0 U8 WAND Emulation%0 0 M2 OCIA Mode%0 0 M4. • Reading Mode End Configuration Reading Mode%0 2 7 1 Trigger ON/OFF%0 2 7 0 Continuous/Trigger OFF%0 2 7 2 Continuous/No Trigger%0 2 7 3 Flash%0 2 7 4 Testing%0 2 7 5 Reserved1%0 2 7 6 Reserved2. • RS-232 Communication Start Configuration RS-232 Communication Parameters Set Up BAUD Rate%0 Y7 0 1200%0 Y7 1 2400%0 Y7 2 4800%0 Y7 3%0 Y7 7 19200%0 Y7 4 Set Up Data Bits 7 Data Bits%0 Y8 0.